How to Remove as well as Replace a Bath Tub.
How to Remove as well as Replace a Bath Tub.
Blog Article
The author is making a few great points relating to How to Install a Bathtub Yourself as a whole in the content underneath.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a tub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is conveniently easily accessible, the task can relocate speedily; if you need to open up a wall surface to eliminate the old tub as well as position the new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make sure you have actually certified on your own for the job and are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you might require a professional plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your restroom if you have currently gotten a new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list must make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before carrying on to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap as well as the sink. Safeguard the tap in position with the supplier provided backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub until the level reviews level.
To install taps, fit all-time low of the outermost versatile faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water as well as inspect all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also check the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a stiff seal, creating the water to penetrate the wall in between the bath and also the tiling, resulting in issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles using waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog posting about How to Install a Bathtub Yourself while doing a lookup on the internet. Sharing is nice. Helping others is fun. Thank you so much for taking the time to read it.
Book With Us Today! Report this page